Gas Transmitter

Model 8CTS is a unique instrument which monitors upto eight 4-20mA signals of three wire transmitters. It allows scaling of the display from a large variety of ranges and resolutions as permitted by the 4-digit LED display. It displays a scaled parameter reading and channel number and units. It provides two alarms and one Fault alarm with corresponding relay contacts. A Tower Lamp is connected for area annunciation visibility of status. Sensors are user provided. STANDARD SPECIFICATIONS Channels : Upto Eight Display : 4 digit LED 10mm high Ranges : 0-2 , 0-5, 0-10, 0-20, 0-25, 0-0-50, 0-100, 0-200, 0-500, 0-1000, 0-1500, 0-1000, 0-2000 Resolution : No DP, 000.0, 00.00, 0.000 Linearity : +0.5 % STANDARD SPECIFICATIONS CONTINUED Power : 110 to 220VAC 50 Hz 1 A Power Supply : 24 VDC to transmitter Current out : Maximum 200mA per sensor Output voltage : 18V on sensing terminals Alarms : Two visual alarms, user settable throughout the range Alarm Relay : One C-NO OR C-NC contact of 50VA rating provided for each set-point Working Temp : 0 to 45C MOC : MS sheet metal powder coated with transparent display window Size O/A : 275x 325 x 130 mm deep Weight : 2.5 Kg IP rating : IP54 Comm. Port : RS485 Modbus RTU For connection to PLC /SCADA Tower lamp : 3 lights ( Red , Yellow & Green) and buzzer.

Often it is more cost effective to replace a sensing head with one which is pre-calibrated at a testing station, thus reducing disruption of the measuring system. Technovation offers such an industry standard 4-20mA transmitter consisting of a gas sensor, its associated circuitry with a display and in a weather-proof housing. FEATURES The three-wire transmitter allows the power and signal to be realized on a three-core wire. One core for positive supply of 12 to 24 VDC, the second core for the 4 to 20 mA output and the third core for the 0 volt supply. The transmitter is immune to voltage drops from long runs and noise from motors, relays, actuators, switches, transformers and industrial equipment. APPLICATIONS Every transmitter is supplied pre-calibrated for a customer specific range. The table below gives an indication of t he gases/ranges offered. These transmitters can be connected to a DC system which supplies the DC Power for the module. They could also be connected to stand alone controllers and PLCs and other data acquisition systems STANDARD SPECIFICATIONS Power Supply : 12 to 24 VDC . Sensor types offered : Non dispersive Infra Red ( NDIR) , Pellistor, DP moisture , RH, VOC, PID & many other types as applicable. Duty : Continuous Display : 4-digit LED Operating temp : 20 oC to 45 oC Operating Humidity : 10 - 90 % RH Operating Pressure : Ambient Load resistance : < 500 Ohms Calibration : Via built in Span and Zero potentiometers. Housing : Poly Carbonate weather proof housing. OR Aluminum JN. Box Enclosure size : 12x8x8.5 (WxHxD) Cms Sampling : Diffusion mode OR in Flow through mode

Often it is more cost effective to replace a sensing head with one which is pre-calibrated at a testing station, thus reducing disruption of the measuring system. Technovation offers such an industry standard 4-20mA transmitter consisting of an electrochemical sensor, its associated circuitry and in a Ex-Proof housing and Ex-proof Sensor head. FEATURES The two-wire transmitter with a local display for measured parameter value allows the signal and power to be supplied on a single wire-pair by modulating the power supply current with the input signal source. The transmitter is immune to voltage drops from long runs and noise from motors, relays, actuators, switches, transformers and industrial equipment.

THE INSTRUMENT These Single Point Wall Mounted Instruments work on 18-24VDC and have a PESO certified Ex proof sensor housing fitted on an Ex-proof Junction box. They use an IP 55 enclosure for the electronics as standard. They are provided with two alarms both audible and visual along with relays and output of 4 20 mA. They are meant for continuous operation of area monitoring with continuous read out, plus vital status indicators FEATURES Type of sensors that can be connected are Electrochemical, NDIR, Pellistor, and Thermal conductivity depending on gas and application. Three Wand operated keys. Two Alarms audible and Visual along with acknowledge and reset buttons, both set points viewable from front face using a wand. One Fault alarm One NO, C, NC potential free relay contact per alarm 4-20 mA Output for PLC, DCS etc. Explosion proof hooter-flasher. APPLICATIONS Used in Hazardous areas for Group IIA, IIB or Group IIC gases. Zone 1 and Zone 2 for gas sensing with appropriate sensor in conjunction with the necessary FLP enclosures for instrumentation or wiring, for detection of toxic or flammable gases in work places or enclosed spaces for safety. Measurement of Hydrogen in battery rooms . CERTIFICATIONS Ex db IIC T6 Gb (0CTa+55C) FOR ZONE 1 & 2 GAS GROUP IIC ASSOCIATED STANDARDS: IS/IEC 60079-0:2017 & IS/IEC 60079-1:2014 BIS : 7800109425 PESO : A/P/HQ/MH/10EX4/7654 (P564213) TE REPORT No: KLPL/Ex/19-082X ISSUE 1 DT: 04-03-2023